Flow characteristics of various swirl-can module designs

Flow measurements were performed on each of six swirl-can combustor module designs under simulated combustor operating conditions to find the design which exhibited a small recirculation zone, intense air mixing, and good fuel distribution in its wake. Conditions that are favorable for producing low oxides of nitrogen emissions and high combustion efficiency were investigated. The recirculation zone, the turbulence intensity and the fuel distribution pattern are obtained in the wake region of the center module of a three module array. The most promising swirl-can module design incorporates two air swirlers which discharge air in opposite directions (contraswirl), mixes the fuel and air upstream of the inner swirler, and has a flow area blockage of 64.3% for the three module array

Aerothermal modeling program, phase 2

The accuracy and utility of current aerothermal models for gas turbine combustors must be improved. Three areas of concern are identified: improved numerical methods for turbulent viscous recirculating flows; flow interaction; and fuel injector-air swirl characterization. Progress in each area is summarized

New trends in combustion research for gas turbine engines

Research on combustion is being conducted to provide improved analytical models of the complex flow and chemical reaction processes which occur in the combustor of gas turbine engines, in order to enable engine manufacturers to reduce the development time of these concepts. The elements of the combustion fundamentals program is briefly discussed with examples of research projects described more fully. Combustion research will continue to emphasize the development of analytical models and the support of these models with fundamental flow experiments to assess the models accuracy and shortcomings

Lean, premixed, prevaporized combustion for aircraft gas turbine engines

The application of lean, premixed, prevaporized combustion to aircraft turbine engine systems can result in benefits in terms of superior combustion performance, improved combustor and turbine durability, and environmentally acceptable pollutant emissions. Lean, premixed prevaporized combustion is particularly attractive for reducing the oxides of nitrogen emissions during high altitude cruise. The NASA stratospheric cruise emission reduction program will evolve and demonstrate lean, premixed, prevaporized combustion technology for aircraft engines. This multiphased program is described. In addition, the various elements of the fundamental studies phase of the program are reviewed, and results to date of many of these studies are summarized

Future fundamental combustion research for aeropropulsion systems

Physical fluid mechanics, heat transfer, and chemical kinetic processes which occur in the combustion chamber of aeropropulsion systems were investigated. With the component requirements becoming more severe for future engines, the current design methodology needs the new tools to obtain the optimum configuration in a reasonable design and development cycle. Research efforts in the last few years were encouraging but to achieve these benefits research is required into the fundamental aerothermodynamic processes of combustion. It is recommended that research continues in the areas of flame stabilization, combustor aerodynamics, heat transfer, multiphase flow and atomization, turbulent reacting flows, and chemical kinetics. Associated with each of these engineering sciences is the need for research into computational methods to accurately describe and predict these complex physical processes. Research needs in each of these areas are highlighted

Results of the pollution reduction technology program for turboprop engines

A program was performed to evolve and demonstrate advanced combustor technology aimed at achieving the 1979 EPA standards for turboprop engines (Class P2). The engine selected for this program was the 501-D22A turboprop. Three combustor concepts were designed and tested in a combustor rig at the exact combustor operating conditions of the 50-D22A engine over the EPA landing-takeoff cycle. Each combustor concept exhibited pollutant emissions well below the EPA standards, achieving substantial reductions in unburned hydrocarbons, carbon monoxide, and smoke emissions compared with emissions from the production combustor of this engine. Oxides of nitrogen emissions remained well below the EPA standards, also

Exhaust pollutant emissions from swirl-can combustor module arrays at parametric test conditions

Improved designs of swirl-can combustor modules were tested using seven-module arrays in a combustor. The combustor was operated over a pressure range of 69 to 207 N/sq cm, a fuel-air ratio range of 0.015 to 0.046, at a constant inlet air temperature of 733 K, and at reference velocities of 23.9 and 30.6 m/sec. The three designs tested performed with high combustion efficiency at all conditions tested and exhibited oxides of nitrogen emissions substantially lower than that of conventional gas turbine combustors. A correlating parameter used to extrapolate oxides of nitrogen emissions to full power or takeoff conditions for large commercial turbofan engines predicts oxides of nitrogen emissions somewhat higher than those specified in the 1979 government emissions standards

Combustion research for gas turbine engines

Research on combustion is being conducted at Lewis Research Center to provide improved analytical models of the complex flow and chemical reaction processes which occur in the combustor of gas turbine engines and other aeropropulsion systems. The objective of the research is to obtain a better understanding of the various physical processes that occur in the gas turbine combustor in order to develop models and numerical codes which can accurately describe these processes. Activities include in-house research projects, university grants, and industry contracts and are classified under the subject areas of advanced numerics, fuel sprays, fluid mixing, and radiation-chemistry. Results are high-lighted from several projects

Pollution emissions from single swirl-can combustor modules at parametric test conditions

Exhaust pollutant emissions were measured from single swirl-can combustor modules operating over a pressure range of 69 to 276 N/sq cm (100 to 400 psia), over a fuel-air ratio range of 0.01 to 0.04, at an inlet air temperature of 733 K (860 F), and at a constant reference velocity of 23.2 m/sec). Many swirl-can module designs were evaluated; the 11 most promising designs exhibited oxides of nitrogen emission levels lower than that from conventional gas-turbine combustors. Although these single module test results are not necessarily indicative of the performance characteristics of a large array of modules, the results are very promixing and offer a number of module designs that should be tested in a full combustor

Assessment, development, and application of combustor aerothermal models

The gas turbine combustion system design and development effort is an engineering exercise to obtain an acceptable solution to the conflicting design trade-offs between combustion efficiency, gaseous emissions, smoke, ignition, restart, lean blowout, burner exit temperature quality, structural durability, and life cycle cost. For many years, these combustor design trade-offs have been carried out with the help of fundamental reasoning and extensive component and bench testing, backed by empirical and experience correlations. Recent advances in the capability of computational fluid dynamics codes have led to their application to complex 3-D flows such as those in the gas turbine combustor. A number of U.S. Government and industry sponsored programs have made significant contributions to the formulation, development, and verification of an analytical combustor design methodology which will better define the aerothermal loads in a combustor, and be a valuable tool for design of future combustion systems. The contributions made by NASA Hot Section Technology (HOST) sponsored Aerothermal Modeling and supporting programs are described